December 22, 2023
Dynamometers
We distribute the highly esteemed Dillon product line, offering the market’s best cost-benefit ratio
Dillon Model X Mechanical Force Gauges
X-C Model Specifications:
The X-C model is available in nine capacities, ranging from 50 lb to 25,000 lb or 50 to 10,000 kg. All variants maintain an accuracy of ±1% of full capacity, except for the 25,000 lb (10,000 kg) models, which have an accuracy of ±2% of full capacity.
These instruments utilize a hardened ball that rotates to ensure vertical alignment under increasing pressure. The ball is securely held in place by a spring clip or retainer, and a threaded mounting hole is located opposite the loading ball at the bottom of the beam. The X-C model caters to both pound and kilogram capacities.
Optional features include:
- Shockless dial indicator: Ideal for installations involving sudden force application or release. Note that a maximum pointer cannot be provided with the shockless dial indicator.
- Maximum load pointer: This pointer remains at the peak load until manually reset. However, it is not available for the X-PP model.
- Zero position on the dial: The factory allows for customization, with options at 12, 3, 6, or 9 o’clock. The standard position is at 12 o’clock.
Muncy™ Industries, your best choice to acquire Dillon dynamometers.
Share the best in Dynamometer and Load Cells
Model X-ST with tension calibration
Dillon offers the Model X-ST in seven capacities from 100 lb to 10,000 lb or 25 kg to 5000 kg. Accuracy is ±1% of full range. (Note: For applications requiring capacities beyond 10,000 lb or 5000 kg in tension, consider the Dillon Dynamometer).
Tension Force Gauges in capacities through 2,000 lb (1000 kg) are supplied with two rod-end connectors. 5,000 and 10,000 lb (5000 kg) capacities are equipped with convenient shackles and pins.
Calibration is available in pounds and kilograms.
Model X-PP with compression/tension calibration
X-C Model Specifications:
Force gauges calibrated in push- pull are available in four capacities in pounds ranging from 50-0-50 lb up to and including 2,500-0-2,500 lb and three metric capacities from 50-0-50 to 1000-0-1000 kg. Accuracy is ±2% of maximum dial reading (based upon total capacity of both compression and tension scales).
Model X-PP gauges in capacities up to and including 500-0-500 lb or 250-0-250 kg are supplied with a set of self-aligning spherical rod-end connectors for tension loading. Force is applied to connectors through a hardened steel pin which must be slip fit in connector holes.
2,500-0-2,500 lb and 1000-0-1000 kg capacity gauges are equipped with two shackle adapters, shackles and pins. Shackles must be removed when compression load is involved. Force is then applied against shackle pins in a suitable test setup.
All push-pull gauges are supplied with a compression-loading spherical ball fitting for compression loading.
Model X Force-Gauge Parts Identification
Principle of Operation
A D-shaped deflection beam is the heart of the Dillon Force Gauge. Machined to close tolerances, beams are heat treated to develop optimum strength and spring characteristics. High-strength aluminum is used in Model X instruments through 500 lb (200 kg). The ranges above this are fabricated from aircraft-quality alloy steel.
Low beam deflection
When measured across the center of top- and bottom-loading holes, the approximate beam deflection is as follows:
|
Low Beam Deflection
|
|
|---|---|
|
Capacity
|
Measurements
|
|
50 to 250-lb
|
(25 to 100 kg) = 0.019”
|
|
500-lb
|
200 kg) = 0.016”
|
|
1,000-lb
|
(500 kg) = 0.018”
|
|
2,000-lb
|
(1000 kg) = 0.011”
|
|
5- and 10,000-lb
|
(2 and 5000 kg) = 0.010”
|
|
25,000-lb
|
(10,000 kg) = 0.022”
|
>> Scroll sideways to see the full table
Overload rating
Accidental overloads up to 30% of capacity can be safely sustained without injury to the dial indicator ir deflection beam. All capacities feature a 5:1 design safety factor.
General Information
- To reset zero, loosen knurled bezel-locking screw and rotate the dial.
- Dillon Model X Force Gauges may be mounted horizontally, vertically, or flat.
- The baked-enamel finish resists corrosion and rust.
- Operating temperature up to 120° F.
Our Services
Find the best service and support to calibrate, and prevent damage to your measurement tools. Request technical support from our highly experienced technical staff.
Our service provides the most accurate and up-to-date information on technical support options.
